Honeywell ML6425, ML7425 Spring Return Electric Linear Valve Actuators Model HONEYWELL ML7425A8018-E 24V 50/60HZ DIRECT COUPLED ELECTRIC VALVE ACTUATOR  Note Replaced ML7425A6016  model Replaced ML7425A3013 model FEATURES   ML6425 and ML7425   • Accurate valve positioning. • Quick and easy installation. • No separate linkage required. • On power failure: ML6425A and ML7425A drive valve stem down. ML6425B and ML7425B draw valve stem up. • Conduit connector is standard. • No adjustments required. • True spring return on power failure. • Low power consumption. • High close-off ratings. • Force-limiting end switches. • Direct/reverse action. • Synchronous motor. • Corrosion resistant design. • Maintenance free.   ML7425   • Position Feedback signal. • Fail-safe position selection for control signal loss. APPLICATION   The ML6425 Spring Return Electric Linear Valve Actuators are floating control actuators used with controllers that provide a switched or floating single-pole double-throw (spdt) output. These actuators operate standard Honeywell valves in heating, ventilating, and air conditioning (HVAC) applications. The ML7425 Spring Return Electric Linear Valve Actuators are modulating control actuators used with controllers that provide an analog output of 0 to 10 Vdc or 2 to 10 Vdc. These actuators operate standard Honeywell valves in heating, ventilating, and air conditioning (HVAC) applications. An internal selector can be used to reverse the direction of action.   read more

STOPPED SELLING This Honeywell PRV valve has been sold off to Resideo and is RM1,300.00/pc x 2 pcs. 8-10 weeks ARO. The name is now Resideo-Braukmann PRV valve. (2-3-2022) Honeywell D06FN Pressure Reducing Valve with Balanced Seat Model D06FN-3/4B * Lead Time 8~10 Weeks! Application   Pressure reducing valves of this type protect installations against excessive pressure from the supply. They can be used for household, industrial or commercial applications within the range of their specification. By installing a pressure reducing valve, pressurisation damage is avoided and water consumption is reduced. The set pressure is also maintained constant, even when there is wide inlet pressure fluctuation. Reduction of the operating pressure and maintaining it at a constant level minimizes flow noise in the installation.   Special Features   • WRAS approved according to BSEN1567 • The outlet pressure is set by turning the adjustment knob • The adjustment spring is not in contact with the potable water • The valve insert is of high quality synthetic material and can be fully exchanged • Integral fine filter • Also available without fittings • Easily retrofittable to convert valve to a reverse-rinsing filter combination • Can be retrofitted with an inlet non-return valve • Inlet pressure balancing - fluctuating inlet pressure does not influence outlet pressure • Light weight • Reliable and proven • Meets KTW regulations for potable water   Range of Application   Technical Data Medium Water Inlet pressure max. 25 bar Outlet pressure 0.5 - 2 bar (preset to 1.5 bar) Operating temperature max. 60°C (permanent) max. 70°C (max. operating pressure 10 bar) Minimum pressure drop 0.5 bar Connection size 1/2' - 2' read more

Deoxidation Chemical Compound  For Copper Tube Brazing (TOYO CLEAN COPPER!!)  Spraying this CLEAN COPPER into copper tubes prevents them from oxidation and keeps clean surface.     US Patent No.6053396 Top: Without TOYO Clean Copper---shows oxidized scales which damage refrigerant cycle.  Japanese Patent No.3231009 Bottom: With TOYO Clean Copper---shows clean surface and no damage for refrigerant cycle.   Superior quality deoxidation spray for copper tube brazing To prevent oxidation at inside of tubes while brazing, CLEAN COPPER has following advantages than nitrogen gas. 1: Easy handling and carry around 2: Save labor works dramatically 3: Can use for any refrigerant 4: No need to clean pipe after use Example of application 1: While place refrigerant gas piping at construction site for commercial, residential air conditioner. 2: Air conditioner or Refrigerator assemble factory.   Method of application 1: Clean well inside of the joint to be brazed 2: Shake well TOYO CLEAN COPPER before use 3: Seal end of the tube. 4: Spray the TOYO CLEAN COPPER inside tube from other end. 5: Seal both ends before brazing 6: Keep seals until cool down (At least 1min) 7: When open seals, white smoke will be out. It is not toxic gas for human How many times need to spray (1500time can spray. Once you press, spray stop automatically after it spray certain amount) 1/4”-5/8” : 1push 3/4”     : 2push 7/8”-1”  : 3push 1-1/8”   : 4 push 1-1/4”   : 5push 1-3/8”   : 6push 1-1/2”   : 7push 1-5/8”   : 8push. read more

A9089 ACCELEROMETER W/ MAGNET FOR TPI9071 & TPI9080   read more

CN20, CN34 SERIES NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR MODULATING AND FLOATING / 2-POSITION CONTROL  Model (Acuator) HONEYWELL CN4620A1001 20NM, 230VAC, DAMPER ACTUATOR, NON-SPRING RETURN CN7220A2007 20Nm,24Vac/Vdc, Modulating and floating/2-position control, Non-Spring return, Voltage Feedback Signal and without aux. Switch CN7234A2008 34Nm,24Vac/Vdc, Modulating and floating/2-position control, Non-Spring return, Voltage Feedback Signal and without aux. Switch HONEYWELL CN7234A2008 34NM, 24VAC/VDC, MODULATING CONTROL, NON-SPRING RETURN (FAIL SAFE FUNCTION) Voltage Feedback Signal AND without aux. Switch   Model (Ball Valve) HONEYWELL VBA216-100F 2-WAY DN100 (4'') PN16 KVS160 FLANGED BALL VALVES (TEMP:-5~120°C)   Complete Set HONEYWELL CN7234A2008 34NM, 24VAC/VDC, MODULATING CONTROL+VBA216-100F 2-WAY DN100 (4'') PN16 KVS160 FLANGED BALL VALVES (TEMP:-5~120°C)   Controller To Use Can use TB7980A, TF243WN or TFM223N/U, depending if you want any external duct sensor or 3-speed fan switch. GENERAL   These direct-coupled damper actuators provide modulating control for: • air dampers, • VAV units, • air handling units, • ventilation flaps, • louvers, and • reliable control for air damper applications with up to 4.6 m2  / 50 sq.ft. (20 Nm / 177 lb-in) or 7.8 m2  / 85 sq. ft. (34 Nm / 300 lb-in) (seal-less dampers; air frictiondependent).   FEATURES   • Self-centering shaft adapter • Access cover to facilitate connectivity • Service/off for safe & easy servicing • Rotation direction selectable by switch • Declutch for manual adjustment • Mechanical end limits • Field-installable auxiliary switches • Mountable in any orientation (no IP54 if upside down) • Mechanical position indicator • CE and UL certified SPECIFICATIONS   Supply voltage 24 Vac/dc ±15%, 50/60 Hz;   Nominal voltage 24 Vac/dc, 50/60 Hz; All values stated hereinafter apply to operation under nominal voltage conditions. Power consumption CN7220A2007 6 VA / 3 W CN7234A2008 6 VA / 3 W Ambient limits Ambient operating limits -20...+60 °C (-5...+140 °F) Ambient storage limits -40...+80 °C (-40...+175 °F) Relative humidity 5...95%, non-condensing Safety Protection standard IP54 as per EN 60529 Protection class II as per EN 60730-1 Overvoltage category II Lifetime Full strokes 60000 Repositions 1.5 million Mounting Round damper shaft 10...27 mm (3/8...1-1/16') Square damper shaft 10...18 mm (3/8...11/16');  45° steps Shaft length min. 22 mm (7/8') Control signal 0(2)...10 Vdc  0(4)...20 mA Input impedance >100 kΩ [0...10 V]  500 Ω [0...20 mA] Feedback signal Limits ± 1 mA at 0...10 V End switches (when included) Rating 5 A (resistive) / 3 A (inductive) Triggering points 5° / 85° Torque rating CN7220A2007 20 Nm (177 lb-in)  CN7234A2008 34 Nm (300 lb-in) Runtime 95 sec (60 Hz) / 110 sec (50 Hz or DC supply) Rotation stroke 95° ± 3° Dimensions see 'Dimensions' on page 8 Weight (without cables) 1.35 kg (3 lbs.) Noise rating 40 dB(A) max. at 1 m Certification CE & UL Torque Per Module (Nm) Calculation NON-SPRING RETURN (ON/OFF) e.g : a) 200 x 200 (mm) [Damper Size (Net)] = 0.2 x 0.2 = 0.04 M2         x 10 (Factor) = 0.4 Nm MFD-S (Motorized Fire Damper) Fail Safe Fast Running (SPRING RETURN) e.g : a) 1,200 x 600 (mm) = 1.2 x 0.6 = 0.72 M2          x 10 (Factor) = 7.2 Nm          b) 1,500 x 1,200 (mm) = 1.5 x 1.2 = 1.8 M2          x 10 (Factor) = 18 Nm          c) 2,500 x 1,000 (mm) = 2.5 x 1.0 = 2.5 M2          x 10 (Factor) = 25 Nm   read more

DIXELL XT110D-4C0TU 1 STAGE DIGITAL CONTROLLER (120V)   read more

F-48 FLOW CONTROLS FILTER CORE (FOR SUCTION) (12PCS/BOX) (PCN: 089559)   read more

FUJIARE 35W 0.3A OUTDOOR FAN MOTOR YDK-35-6A (FC-1217)   read more

NO LONGER SELLING UNDER HONEYWELL Honeywell C6045D1043 Pressure Switch Honeywell Pressure switch for general gas- and air application C6045D For monitoring pressure of air and non-aggressive (fuel)gases. Kind of pressure: differential pressure, relative Pressure connection: positive pressure: G1/4'' negative pressure: G1/8'' Electrical connection: PG13,5 Protection class: IP40 Housing material: aluminium die casting Media temp.: -15...70C Ambient temperature: -15...70C Switch function/capacity: SPDT Microswitch 250Vac; capacity: 2 A (inductive); 10 A resistive Approvals: CE (EN1854) - PIN: 0063AR3085/2 Mounting position: horizontal or vertical Large mambrane for maximum accuracy Direct mount on G1/4'' connection Pressure adjustment range: 0.2...3mbar Max. pressure: 100mbar read more

BELIMO SM24A-SR MODULATING DAMPER ACTUATOR 20NM, 24V AC/DC, 50/60HZ (RUNNING TIME 150S) Modulating damper actuator for adjusting air dampers in ventilation and air-conditioning systems for building services installations    • For air dampers up to approx. 4 m2 • Torque 20 Nm • Nominal voltage AC/DC 24 V • Control: Modulating DC 0 ... 10 V • Position feedback DC 2 ... 10 V   read more